Posted 20 hours ago

Caution Oil Pipeline Below Warning Tape - 20 Metre Custom Cut Length

ZTS2023's avatar
Shared by
Joined in 2023

About this deal

What are the different pipe marking tapes available?Each pipe must be clearly identified using the correct pipe identification banding. Each tape is different depending on what is within the pipe, the most common are: The British Pipe Marking Standard requires that, at a minimum, pipe marking signs must be located on both sides of valves, service appliances, bulkheads, wall and floor penetrations, as well as any other place pipe contents identification is needed. These regulations are important to follow otherwise the marking will be invalid. The tape serves the dual purpose of (1) allowing location from above ground and (2) providing a visual warning to prevent third party damage


Directly buried fuel supply pipes should be protected against the risk of accidental damage caused by digging. The recommended installation method is as follows: How would I know if I need to use pipe marking tapes?Pipe marking signs are an essential part of dealing with potential safety issues, pipes that are exposed specifically above ground are a risk that must be highlighted using marking tape. The meaning behind this is due to the safety of those working around the pipes to enable the pipes to be visible and therefore less dangerous. When it comes to industrial piping, workers need a way to accurately and consistently identify the hazards they may face. Furthermore, BS 1710 states that pipe labeling is required if the pipes are actively carrying fluids or gases. Pipe marking is a vital part of reassuring the health and well being of workers around pipes carrying gases, liquids or other elements that could potentially cause harm. The color of the pipe marking is specific to the element the pipe is carrying, which informs workers of the danger.

Underground Warning Tape for marking buried services including underground cables and pipes - premium grade underground warning tape with ENATS 12-23 approval for cable and pipe marking. A fire valve is an essential safety feature of a fuel supply installation, which will stop the supply of fuel in the event of a fire or an overheat situation occurring at the appliance. The valve should be located outside the building, before the point of entry, and be activated by a remote sensor. Existing fuel supply pipes that are not accessible outside of the building, and do not have a fire valve, can have one added at the first point where the pipe appears internally. This is not permitted on a new pipe installation, but it can improve the safety of an existing installation. Fire valves are also required for externally located appliances. Your OFTEC registered technician will be able to offer advice on the correct selection and positioning of fire valves. Annual inspection of compacted sand is laid on the bottom of the trench, the fuel supply pipe positioned, and a further 40mm of compacted sand is laid above the pipe

Pipe Marking Tape UK - Compliant and Cost-Effective | Seton Pipe Marking Tape UK - Compliant and Cost-Effective | Seton

For best performance, fuel supply pipework should take the most direct route between the fuel tank and burner, while avoiding high points in the pipework, the creation of trip hazards, or anything likely to damage the pipe and joints. Pipes should be supported by purpose made clips and attached to permanent structures, such as a wall. A garden shed or wooden boundary fence is not classed as a permanent structure because it will deteriorate with age and any movement may damage the pipe and fittings. Buried fuel supply pipes In 2021, oil (kerosene) continues to be the most widely used fuel in off-grid homes. However, to reflect that a renewable liquid fuel, such as HVO may soon be available (see our future heating section) we have used the term liquid fuel in this guide to include both oil and low carbon liquid fuels. Oil Pipeline Detectable Warning Tape. 75mm x 50M. A plastic warning tape with a twin, stainless steel tracer wire system. Two wires are laminated within the tape. The continuous ‘wave’ pattern, allows the tape to stretch by over 25%, thus helping combat underground movement.

Fuel supply pipes should be buried at least 300mm clear of other underground services such as water and electricity. Joints should be avoided in buried pipework, if possible. If joints need to be made, they should be within an inspection chamber. Entry into buildings

Tape | Pipe Identification Tape | Label Source Pipe Marking Tape | Pipe Identification Tape | Label Source

Fuel supply pipes are a vital part of any liquid fuel-fired heating system and it is important that they are installed and maintained correctly to ensure system reliability and safety. Correct installation also helps to avoid the risk of leaks, which can cause pollution and are costly to clean up. This guide applies to pipes that carry fuel to liquid fuel-fired appliances of up to 70kW output which are located at properties used primarily for domestic purposes. Fuel supply pipes entriforce Stokbord underground cable protection covers are heavy duty cable protection covers designed to withstand damage and protect HV cables from plant and hand tools - suitable for underground high voltage cable protection (22kV, 33kV, 66kV, 132kV and up to 400kV).

Domestic fuel supply pipes are usually made of plastic-coated soft copper tubing that can be easily manipulated.. Plastic pipe systems are also available but must only be used below ground and outside of buildings. Fittings and jointing materials must be suitable for the type of pipe and fuel being used. Liquid fuel supply systems OILS: Oils, including fuels and hydraulic or transformer fluids, need to be labeled with a brown outer ring.

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment